Stanton SA-12 Bedienungsanleitung PDF herunterladen (Seite 3)

SA-12 FUNCTIONS & FEATURES

• Focus Fader V2 Digital Optical

Crossfader

(Patent Pending)

with

curve adjustment and reverse switch.

• OS2

(Patent Pending)

Optical Scratch

switches with lock feature

• Removable effects module

(Patent

Pending)

. SA-12 includes MOD1:

Pitch Shifter, Flanger, and Delay; with

Parameter and Mix controls.

• Effects fully assignable

• Foot pedal output to control effects.

• 3 position cue select

(Patent Pending)

Pre CF Cue / Post CF Cue / Master.

• 2 line, 2 phono, and 1 mic/line (switch-

able) inputs.

• Program Reverse.

• 3 band EQ with complete kill, Gain,

and Pan control per channel.

• Program Faders reverse switches &

curve adjustments.

• Headphone mute.

• Cue Pan Fader

• Dual headphone inputs (1/4 and 1/8

mini-jack).

• TRS balanced Master output.

• Mono-Stereo Switch.

• Output Trim control.

• Quiet-Start feature to avoid pops /

noise when mixer is powered on.

Removable Effects Module

The MOD1 removable effects module

includes 3 effects: Pitch Shifter,

Flanger, and Delay. All effects have

adjustable parameters and levels, can

be assigned (turned on / off) to all

channels or master output, and can be

turned ON/OFF using any standard

footswitch via the remote Start output.

OS2 Optical Scratch Switch

These ultra quiet, non friction

phono/line switches allow you to trans-

form without the clicking or static noise

found in other line switches. Now

including a special feature that locks

the last position of the switch.

3 position Cue Select

This switch allows you to set your cue

source to PFL/Pre -crossfader,

PFL/Post-crossfader, or Master. This

unique PFL/Post-crossfader features

allows you to practice and cue your

scratches using the crossfader

(instead of the cue pan fader) during a

live show.

Mic/Line Channel

The SA-12’s Mic/Line channel features

an input selector switch activating a 3rd

line input (RCA) or a standard micro-

phone input, both controlled by a 2-

band EQ with gain adjustment. This

can also be used as a "session in" with

volume control for linking additional

mixers.

It’s only the 3x champion, DJ Craze signature mixer! This battle mixer has the all

the quality of a club mixer and meets all the requirements of today's Turntablist.

After years in the making the ultimate Scratch DJ mixer is here and ready for bat-

tle.

FEATURES:

remove the slider assembly (C), ensuring that the wiper contacts (D) are

not damaged as this will affect the operation of the fader. Clean the slid-

er assembly by gently wiping the wiper contacts and slider bearings (E)

using a tissue or cotton bud. If slider bearing are exessively worn, as indi-

cated by exessive slider rocking then contact Stanton for replacement.

Remove the single upper screw on the

opposite end block to remove the guide rail.

Clean the guide rail (F) with a tissue or

cloth, removing all traces of dirt and conta-

mination.

Remove the fader track (G) by slowly with -

drawing from the unit. Place fader track on

desk or working surface with black contacts facing upwards.

If necessary, the track can be washed in warm water, wiped

gently then dried thoroughly using a dry cloth. Use a lint free

cloth or swab to wipe the tracks and check for marks along

the track. (Note: Lint free cloth should be used to avoid

dust/fibres being deposited on the track). If the track appears

exessively worn, or if cleaning does not improve operation,

replacement may be necessary.

Examine the center channel of the fader body and if dirty, clean using cot-

ton buds.

Re-assemble and lubricate the fader as follows:

6.1

) Secure the end block and guide rail onto the fader body.

6.2

) Insert track into the fader body.

6.3

) Insert slider assembly onto guide rail and into the fader body. Move

slider from end to end to disperse the oil evenly. Carefully wipe away any

excess oil using a tissue or cloth.

6.4

) Lubricate the guide rail by placing one drop of silicon liquid oil onto

the guide rail (F).

6.5

) Insert dust cover.

6.6

) Insert fader track back into fader body with wires coming out open

end of fader body.

6.7

) Secure the remaining end block ensuring that the track wires (I) are

not pinched between the endblock and fader casing.

Once assembled, move the slider from end to end to ensure operation is

smooth.

Attach fader to fader plate. (NOTE: As noted earlier if you do not want to

change positioning of fader, keep the 2 fader plate screws loose and shift

the fader until it is aligned with the marks you created in step 1, then tight-

en fader plate screws.)

FADER CLEANING AND REPLACEMENT

1 2 3 4 5 6

Kommentare zu diesen Handbüchern

Keine Kommentare

Stanton SA-12 Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern